|
|
| (2 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| {{Era|GOO}}[[Image:SpartanIII.jpg|thumb|200px|Mark II SPI Armor]]'''Semi-Powered Infiltration Armor''', colloquially called "'''SPI Armor'''", was an [[armor]] system used by the [[United Nations Space Command]]. Though more advanced than the [[ODST]] [[Body Suit]]s, it was far less advanced and less powerful than the [[MJOLNIR Armor]] used by the [[Spartan-II]]s. Its main benefit was that it was drastically cheaper to produce than the MJOLNIR armor. This armor was designed with an emphasis on stealth rather than raw power. It features [[Camouflage Cloak|special photo-reactive panels]] that mimic the surrounding textures, effectively being the UNSC equivalent to the [[Covenant]] [[Active Camouflage]] systems. It has been described as part legionnaire mail, part tactical body armor, and part chameleon.<ref>[[Halo: Ghosts of Onyx]] page 16</ref>
| | #REDIRECT [[Semi-Powered Infiltration armor]] |
| | |
| ==SPI Mark I==
| |
| The SPI armor Mark I was used by the Spartan-IIIs of [[Alpha Company|Alpha Company]]. It featured hardened plates and photo-reactive panels. Though advanced compared to standard UNSC infantry armor, it could only take a few glancing blows before failing<ref>[[Halo: Ghosts of Onyx]] page 14</ref>. The armor featured full body armor with a helmet and [[HUD]], and a supply of breathable atmosphere; though only enough for [[List of "Seven" references in Halo|7]] minutes, compared to the MJOLNIR armor's endurance of 90 minutes. It is also equipped with a cushioning layer of liquid nanocrystals that provided more ballistic protection than three centimeters of [[wikipedia:Kevlar|Kevlar]] diamond weave without the bulk. The featured photo-reactive panels, gave the Spartans of Alpha Company active camouflage. The camouflage patterns however shifted irregularly and imperfectly, which made the photo-reactive panels unmatched against the Covenant elites Camouflage technologies. This was because the SPARTAN III program didn't allow enough time to get the photo-reactive panels working properly.
| |
| | |
| ==SPI Armor Mark II==
| |
| | |
| The SPI armor Mark II was a more advanced version of the armor, first used by the drill instructors of Beta Company and then by the Spartans of Beta Company. They had new photo-reactive coating to boost camouflaging properties. There were also numerous experimental refits to gel ballistic layers, upgraded software suites, and other functions. Although the new photo-reactive coating could mimic a wide range of EM(Electro Magnetic) radiation, it was still sensitive to overload, which is why it takes the suit a few moments to reset after a flash-bang for example<ref>[[Halo: Ghosts of Onyx]] page 113</ref>.
| |
| | |
| It was proposed in [[2537]] for Alpha Company, but the request was denied because the armor was over budget. After the "successful" operation of Alpha Company, the Mark II armor was approved for mass production.
| |
| | |
| After the augmentation of Gamma Company, small adjustments where installed into the SPI Armor Mark II.
| |
| | |
| ==Advantages vs. MJOLNIR Armor==
| |
| #The armor is a lot cheaper and easier to mass-produce.
| |
| #Includes [[Camouflage Cloak|special photo-reactive panels]] that act as active camoflage.
| |
| #It could be transported easier, because it is not as thick or heavy as the MJOLNIR armor.
| |
| | |
| ==Disadvantages vs. MJOLNIR Armor==
| |
| #Has no energy shield that the SPARTAN-IIIs require considering the amount of danger they face.
| |
| #Does not give the SPARTAN-IIIs the same amount of enhanced strength, speed and agility as the MJOLNIR does for SPARTAN-IIs.
| |
| #After long use, tends to heat up and can become very uncomfortable.
| |
| #Since the AC plates take time to recover after explosions such as a flash bang grenade, the SPARTAN-III is visible until the plates recover.
| |
| | |
| ==Notes==
| |
| * Some screenshots released by Bungie lead to fans speculating that they would be able to use SPI armor in [[Halo 3]]. However, the armor was later determined to be [[Mark VI MJOLNIR Powered Assault Armor/V variant]]. The name and changes in appearance are purely cosmetic, however, having no impact on gameplay. This has been confirmed by [[Bungie]].
| |
| | |
| * In Halo 3, a player can use the different armor permutations to construct a relatively close visual approximation of SPI armor, using the Hyabusa shoulder armor, EVA helmet, and either the Scout or the EOD chest armor, or another chest armor of the players choice, though a more correct look would be to have the Hayabusa shoulder plates on the forearms instead.
| |
| | |
| Since armor permutations are limited, the above combination is the closest that a player can come to having Spartan III armor, in a visual sense.
| |
| | |
| == Sources ==
| |
| <references/>
| |
| | |
| == Links ==
| |
| === Internal ===
| |
| *[[Halo: Ghosts of Onyx]]
| |
| === External ===
| |
| *[http://www.scifi-meshes.com/forums/3d-wips/15883-spi-armor-halo-universe.html SPI Modelling Thread (Sci-Fi Meshes.com)]
| |
| | |
| | |
| [[Category:UNSC]]
| |
| [[Category:Technology]]
| |
